The first cold days arrive, you switch the AC to heating, and it blows lukewarm or cold air. Or it heats, but the room never gets warm. Before you decide the unit is broken, check these seven things. Most can be solved in a few minutes, and for the rest you will at least know what to tell the technician.
Short answer
An AC usually doesn't heat because it's in the wrong mode, because it's defrosting the outdoor unit, or because the filters are dirty. If all of that is fine and it still blows cold air, the cause is usually low refrigerant, a sensor or a valve, and you need a technician.
Need a pro right away? Book AC service in the MostApp app and pick a time.
7 common reasons your AC isn't heating
1. The AC isn't in heating mode
It sounds obvious, but it's the most common cause. The remote should show the sun symbol (HEAT), not AUTO, COOL or FAN. In FAN mode the unit only moves room-temperature air. Also make sure the set temperature is a few degrees higher than the room.
2. It was just switched on
In heating mode, the AC first warms up the coil and only then starts the fan. For the first few minutes it can look like nothing is happening. Wait five to ten minutes before deciding it's not heating.
3. The outdoor unit is defrosting
When it's cold and damp outside, ice forms on the outdoor unit. The AC then pauses heating to defrost: the indoor unit stops blowing and the light often blinks. This lasts a few minutes and is completely normal. If it happens constantly and the outdoor unit is covered in ice, call a technician.
4. Dirty filters
Clogged filters in the indoor unit reduce airflow, so the AC heats weakly and uses more power. Lift the front cover, take the filters out, rinse them in lukewarm water and put them back only when completely dry. If you haven't done this since summer, it's probably time.
5. It's too cold outside
An AC heats by pulling heat from the outdoor air. In hard frost its efficiency drops, and older non-inverter units can almost stop heating. Newer inverter units work at lower temperatures, but they also heat less when it's very cold.
6. Low refrigerant
If the mode is right and the filters are clean but the air is still lukewarm, the system may be losing refrigerant. Refrigerant doesn't get “used up”, so low levels mean a leak somewhere. You can't check this yourself: a technician measures the pressure, finds the leak and refills the system.
7. Faulty valve, sensor or electronics
The four-way valve switches the AC between cooling and heating. If it fails, the unit cools even when set to heat. The same goes for temperature sensors. Many units show an error code on the display or blink the light in a specific pattern.
What you can check in five minutes
- The remote is set to HEAT (sun) and the temperature is higher than the room.
- The remote's batteries work. If the AC doesn't respond, replace them first.
- The filters are clean.
- Nothing blocks the outdoor unit, and it isn't buried in snow or leaves.
- The light isn't blinking constantly and there's no error code. If there is one, write it down; it helps the technician a lot.
When to call a technician
- After 15 minutes in heating mode, the AC still blows cold air.
- An error code appears or the light blinks constantly.
- The outdoor unit is constantly iced over or makes unusual noise.
- The AC heats, but much more weakly than last winter.
- Water drips from the indoor unit or there's an unpleasant smell.
What the technician does and what it costs
The technician checks the mode and settings, cleans the filters and coil, measures refrigerant pressure and tests the valve and sensors. If the problem is dirt or refrigerant, the job is usually done in one visit. Electronics or valve faults sometimes need a spare part.
On MostApp you see the technician's hourly rate before you send a request. The final amount depends on what's needed: cleaning, a refrigerant top-up or a part replacement.
FAQ
Why is my AC cooling instead of heating?
Most often the remote is in the wrong mode. If it's set to HEAT and still cools, the four-way valve is probably faulty, and a technician needs to fix it.
Why is my AC only blowing air and not heating?
It's either in FAN mode, defrosting the outdoor unit, or the filters are very dirty. If none of these, the refrigerant should be checked.
Why is the light on my AC blinking?
On most models, blinking during heating means defrosting or warming up before the fan starts. If it blinks constantly and the AC doesn't work, it's an error code you can look up in the manual or show to a technician.
Does an inverter AC heat below zero?
Yes, inverter units heat below zero, but less efficiently. The colder it is outside, the weaker the heating and the higher the power use.
Book an AC service on MostApp
If you've checked everything in this article and your AC still won't heat, book an AC service. In the app you choose a technician, see their hourly rate and pick a time. Technicians are available in Belgrade and Novi Sad.



